If you are getting hot water even though the digital display does not turn on then the problem is with the electronic board. If you are not getting hot water this could be an error in the plumbing or electrical connections. Call our customer support line with your installer at 877-474-6473 to troubleshoot the unit. How do I turn on my empire heater? empire heaters troubleshooting.
Why is my EcoSmart water heater not working?
If you are getting hot water even though the digital display does not turn on then the problem is with the electronic board. If you are not getting hot water this could be an error in the plumbing or electrical connections. Call our customer support line with your installer at 877-474-6473 to troubleshoot the unit.
Why is my tankless water heater not igniting?
If the flow is too low, the burner will not ignite. Low pressure is one of the most frequent tankless water heater problems and is easy to fix. An inlet filter is dirty and clogged. Check for the correct hot and cold water installation (ensure that lines are not installed in reverse order).
Where is the reset button on a tankless water heater?
The red button on the water heater is where the reset button is located. There are two buttons for each thermostat in some water heaters. The metal plate that holds the thermostat in place may have to be removed to access the reset button.
How old is my EcoSmart water heater?
EcoSmart does not encode the date of manufacture in the serial number of their water heaters, but you can call their customer service line at 877-474-6473 with the number, or email them at [email protected], and they will provide you with the manufacture date.
What does E4 mean on EcoSmart tankless water heater?
An E4 error code on your 45 model tankless water heater, indicates that there is an issue involving the flow meter sensor (also referred to as cold water temperature sensor.) This means that the flow meter is not sending a signal to the computer which starts the machine.
How long do EcoSmart tankless water heaters last?
– Tankless water heaters can last over 20 years, much longer than any other water heater. – Tanks only last 10-12 years.
What is activation flow rate?
Activation and energy consumption control refer to the minimum flow rate at which the unit activates, how it activates, either by flow switch or flow sensor, and how it controls the amount of energy it consumes. … Most flow switches are designed to activate the units at flow rates between ¾ to 1 GPM.
How do you turn on a tankless water heater?
Turn the gas shut-off valve counterclockwise to the “On” position. Turn the electric breaker back on or turn on the power switch to start the unit.
Why is my electric tankless water heater not working?
First, reset any tripped circuit breaker, and replace any blown fuse. Next, check if power is being supplied to the electric water heating element thermostat. … When the water’s not hot enough, the problem can be an undersized water heater, crossed hot and cold connections, or a faulty heating element or thermostat.
What does a flow sensor do on a tankless water heater?
A flow switch is used to detect the presence of water flow and turns on the system to heat the water. Whenever there is a hot water demand, a reed sensor within the tankless water heater identifies the demand and initiates the heating process.
How do you turn on a electric water heater?
- Step 1: Check for Any Open Valves, or Faucets Close Them Up. …
- Step 2: Turn the Cold Water On. …
- Step 3: Take Out the Safety Tag. …
- Step 4: Turn on the Breaker.
How old is my envirotemp water heater?
Envirotemp water heater age is usually encoded in the first four digits of the serial number as YY WW where ww is the week number.
Where is date on water heater?
Check the label Check for a manufacturer label on the side of your water heater — this should include the installation date. If the label is missing, or the installation date is not listed, you can use the serial number to determine the age of your unit.
What is the life expectancy of a water heater?
The type of water heater and where you are located: While many say 8 to 12 years is the expected life for a standard gas-powered water heater, this range can change and be very dependent on where you are located. The level of sediment in your tank affects the lifespan of your water heater.
What does E5 mean on Eemax tankless water heater?
Answer: Rheem RETEX-27 E5 Error code, High Flow Rate. If the LED control board is displaying an E5 error code, the desired volume of water is too high to reach your desired preset temperature and you will need to slow down the Flow rate if needed .
How do I connect my EcoSmart light bulb?
Select “Ecosmart”. Follow the SmartThings app instruction to click “Next” – “Next” – “Next”. Scan the QR code on the bulb or click “I don’t have a code” to connect the bulb. Click “Done”, The LED bulb will now connect as “Ecosmart Bulb”.
Who makes EcoSmart?
Lighting Science Group is proud to be the technology provider behind The Home Depot’s ECOSMART lighting products, and deliver an American solution for our energy and environmental challenges.” The A19 ECOSMART LED bulb is available on Home Depot’s website () and in stores nationwide.
Who owns EcoSmart tankless water heaters?
Eemax, a leading manufacturer of commercial, industrial, and residential electric tankless water heaters, has acquired EcoSmart, a fast-growing consumer brand for residential electric tankless water heaters based in Miami, FL.
Where are EcoSmart water heaters made?
Introduction to EcoSmart Tankless Water Heaters Water heaters are made in China. The brand makes EcoSmart electric and gas water heaters.
How do you turn off a Rinnai tankless water heater?
– Turn off the gas at the manual gas con- trol valve, usually located immediately below the water heater. – Turn off the incoming water supply. This can be done at the isolation valve immediately below the water heater or by turning off the water supply to the building. Safety alert symbol.
Can I install an electric tankless water heater myself?
Installation. While it is possible to install your own tankless water heater, it’s not a job for inexperienced do-it-yourselfers. There are a number of different sizes and styles of tankless water heaters, including propane, natural gas and electric, along with single-room or whole-house sized models.
How do I install an electric tankless water heater?
- Step 1: Cut circuit breaker and water supply.
- Step 2: Drain water heater.
- Step 3: Remove front cover.
- Step 4: Mount water heater.
- Step 5: Connect pipes.
- Step 6: Install flow and pressure valves.
- Step 7: Bleed hot water system.
Where is the pilot light on a tankless water heater?
To check, you’ll need to access the water heater. The pilot light on most water heaters is located at the base of the unit, below the gas control valve. Open the access panel or door to the burner chamber and look inside. There, you’ll find the pilot light tube, which should have a steady blue flame.
How do I turn my hot water heater back on?
- Step One – Close Open Faucets. …
- Step Two – Turn On the Cold Water Supply. …
- Step Three – Light the Pilot Light. …
- Step Four – Turn the Gas Valve to On. …
- Step One – Close Open Faucets. …
- Step Two – Turn On the Cold Water Supply. …
- Step Three – Remove the Lock Out Safety Tag.
How do I know if my water heater is working?
- You don’t have enough hot water. …
- You have varying water temperature issues. …
- You have a leaking water heater. …
- You notice reduced water flow. …
- You’re hearing some concerning sounds. …
- You have smelly or discolored water. …
- Your water heater is on the older end of the spectrum.
How do I adjust my eemax water heater?
If the water is too hot: turn the temperature adjustment shaft counter- clockwise about 1/8 of a turn and wait 15-20 seconds. If the temperature remains too hot, repeat this step until the desired temperature is achieved. Congratulations ! Your Eemax tankless electric water heater is fully installed and ready for use!
How do I turn on the heater?
- To turn on your gas heater, locate the knob for starting. …
- Turn the knob to “Pilot,” and then push down on the “Ignite” button. …
- Once the pilot light comes on, hold down the Ignite button for 10 to 15 seconds.
